# FLAT PLATE HEAT EXCHANGE INSTALL - FEMA REGIONAL CENTER, DENTON TEXAS Canonical: https://abierto.us/opportunities/flatplateheat - Solicitation number: FLATPLATEHEAT - Notice type: Sources sought - Status: Closed. Deadline was February 12, 2025 at 10:00 AM EST - Department: Department of Homeland Security - Agency: Federal Emergency Management Agency - Contracting office: FEMA (70FH10) - NAICS: 23822 Plumbing, Heating, and Air-Conditioning Contractors - Place of performance: Denton, Texas - County: Denton County (FIPS 48121). https://abierto.us/counties/denton-county-tx-48121 - City: Denton. https://abierto.us/cities/denton-tx-4819972 - First posted: February 6, 2025 - Last posted: February 6, 2025 - SAM.gov: https://sam.gov/workspace/contract/opp/0a1a8e0ad0a849779823e4982d449e93/view ## Description The Department of Homeland Security (DHS) Federal Emergency Management Agency (FEMA) has a requirement for Flat Plate Heat Exchange Install in the Denton, TX FEMA Regional Center. This notice is a Request for Information only and is not a request for quote or solicitation. The government will not reimburse parties for responses to this notice. FEMA is requesting interested parties submit an interest and capability statement per the information provided below. PURPOSE The objective of this project is to enhance energy efficiency and temperature control in the FRC building located at 800 N. Loop 288, Denton, Texas 76209. The requirement includes installing a flat plate heat exchanger system to make the property more energy efficient. The goal is to optimize power consumption while saving wear and tear on the new chillers with the intent of improving climate control within the building. During the winter months, when the flat plate system is running the chillers can be turned off and the building can be cooled with outside air and two pumps. PROJECT DESCRIPTION The primary goal of this project is to install a new flat plate system with all the required pipe work, valves and controls connected to the Metasys system. The purpose is to require a design to save power and wear on the new chillers in order to make the HVAC system more efficient as the flat plate has no motors or moving parts so when the flat plate is engaged it consumes NO POWER. The installation should include: 1. The new flat plate unit. The sizing of the new unit to be determined by the contractor. 2. Removal of any abandoned fan units or equipment in the central plant space to make room for the new equipment. To include attached ductwork or pipework. Be aware the units may contain asbestos or lead based paint as the vintage of the property is pre-1989. 3. Installing new and rerouting the original pipework on the condenser and chilled water sides to install the flat plate. And adding necessary manual valves to control the flat plate. 4. All removed items will be disposed of in an environmentally sustainable manor off the Region 6 site. 5. Temperature check points will need to be installed and tied into the Metasys system so the system can be monitored from the Metasys central control computer. EXPECTED PERFORMANCE REQUIREMENTS The contractor will submit a detailed Performance Work Statement (PWS) outlining the tasks, schedules, and resource requirements. The expected PWS will require the following: A project schedule, including a Gantt chart outlining all milestones. Provisions for minimizing disruptions to employees, including noise levels, power outages, and operational impacts. Physical oversight during the entire project lifecycle. The contractor must comply with FEMA's Build America, Buy America Act (BABAA), and any commercial building codes and regulation requirements and/or follow the procedure for waiving "Buy America" preferences (if necessary). For this Request for Information, the government is requesting interested Vendors submit their interest and capability to Daisy.Joseph@fema.dhs.gov not later than 10:00 a.m. (ET) on 12 Feb 2025. The interest and availability statement shall include but not limited to: 1. Company's Name, Address, Point of Contact, Phone Number, Business Size, and SAM.gov UEID Number. 2. Summary of experience and years of experience as it relates to the government's requirement. 3. Provide best available date to start the project. Vendor response should include a total of not to exceed three (3) pages. ## Publications - February 6, 2025: Sources sought, due February 12, 2025 at 10:00 AM EST. Notice 0a1a8e0ad0a849779823e4982d449e93. https://sam.gov/workspace/contract/opp/0a1a8e0ad0a849779823e4982d449e93/view ## Points of contact - Daisy Joseph, daisy.joseph@fema.dhs.gov --- Source: SAM.gov Contract Opportunities bulk extract. Confirm deadlines on SAM.gov before responding. Cite https://abierto.us/opportunities/flatplateheat.